SICK · SICK

Датчик потока SICK FTS-H100F04A, артикул 1091147

MPN / артикул: 1091147

Датчик потока SICK FTS-H100F04A, артикул 1091147.

Производитель автоматикиSICK
Артикул1091147
РазделSICK
Единицашт
Фото товара

Датчик потока SICK FTS-H100F04A, артикул 1091147

1 / 1

Внешний вид может зависеть от исполнения. Перед заказом сверяйте маркировку и артикул.

О модели

Описание

Датчик потока SICK FTS-H100F04A, артикул 1091147.

Напряжение питания: 9 V DC ... 30 V DC 1) [примечание 1]. Коммутационный выход: 2xPNP. Выходной сигнал: 2 push-pull digital outputs (Q2 configurable for IO-Link; Q2 configurable as pulse output / digital input) for flow and temperature. Функция выхода: NO/NC. Интерфейс связи: IO-Link, IO-Link V1.1, COM3 (230.4 kbit/s).

Семейство: T-Easic FTS. При подборе сверяйте артикул 1091147 и полное обозначение FTS-H100F04A.

Примечания к параметрам (EN)

1. 1) All connections are reverse polarity and overload protected. Q1 and Q2 are short-circuit protected. Use an energy-limited circuit for the voltage supply as per UL61010-1 3. Outp. 2) Per output.

2. 1) Place probe tip in the center of the pipe to ensure the highest measurement accuracy. 2) The measuring range limit value depends on the medium used. 3) At medium temperatures above 100 °C, the distance between the bottom of the housing and the top of the process connection adapter must be at least 25 mm. If a SICK process connection adapter is used, the 60 mm probe cannot be used at process temperatures above 100 °C because the distances cannot be maintained. 4) According to the Pressure Equipment Directive 2014/68 / EU: Good engineering practice, according to Article 13 for media of media group 2 (other substances).

3. 1) According to the UL approval: degree of contamination 3 (UL61010-1: 2012-05); air humidity: 80% at temperatures up to 31 °C; installation altitude: max. 3,000 m above sea level.

4. 1) Only with M12 male connector attached / not UL-tested.

5. 1) Under reference conditions with water, diameter of inner pipe 25 mm, vertical installation in pipe, probe tip in tube center, fully-filled pipe without air bubbles, speed from 10 cm/s to 100 cm/s, inlet zone > 30 cm, outlet zone > 30 cm, 26 °C ± 1 °C, 2 bar ± 1 bar. 2) Filter off. 3) Under reference conditions with water, pipe diameter 25 mm, vertical installation in pipe, tip in pipe center, fully-filled pipe without air bubbles, speed = 100 cm/s, inlet zone > 30 cm, outlet zone < 30 cm, 26 °C ± 1 °C, 2 bar ± 1 bar.

Перед заказом проверьте артикул 1091147, исполнение и присоединительные параметры. Менеджер подтвердит комплектацию по запросу.
Параметры

Технические характеристики

Модель
FTS-H100F04A
Напряжение питания
9 V DC ... 30 V DC 1) (прим. 1)
Коммутационный выход
2xPNP
Выходной сигнал
2 push-pull digital outputs (Q2 configurable for IO-Link; Q2 configurable as pulse output / digital input) for flow and temperature
Функция выхода
NO/NC
Интерфейс связи
IO-Link, IO-Link V1.1, COM3 (230.4 kbit/s)
Подключение
M12 round connector x 1, 4-pin
Присоединение к процессу
Without process connection (adapter needed for installation)
Разрешение
0.01 m/s Speed; 0.1 L/min volume; 0.1% relative (via IO-Link)
Температура процесса
–40 °C ... +150 °C 3) (прим. 2)
Температура окружающей среды при работе
–40 °C ... +70 °C 1) (прим. 3)
Степень защиты
IP67 / IP69 1) (прим. 4)
Время отклика
< 2.5 s 2) (прим. 5)
Давление макс. (Бар)
100
Диаметр зонда (мм)
8
Диапазон измерения (см/с)
3-150
Измерение температуры
да
Измеряемая среда
Water and oil-based liquids
Класс защиты
III
Масса
200 g
Материал корпуса
Stainless steel 1.4305 / 303
Резьба разъема
M12
Серия
T-Easic FTS
Температура эксплуатации (°C)
-40…+150
Тип датчика потока
Калориметрический (в корпусе с зондом)
Единица продажи
шт
Артикул производителя
1091147
Инженерный подбор

Не нашли точную модель?

На отдельной странице можно распознать маркировку по фото или загрузить BOM из Excel, Word и CSV.