Датчик потока SICK FTS-I060F14A, артикул 1091146
Датчик потока SICK FTS-I060F14A, артикул 1091146.
Описание
Датчик потока SICK FTS-I060F14A, артикул 1091146.
Напряжение питания: 9 V DC ... 30 V DC 1) [примечание 1]. Коммутационный выход: 2xPNP. Выходной сигнал: 2 push-pull digital outputs (Q2 configurable for IO-Link; Q2 configurable as pulse output / digital input) for flow and temperature. Функция выхода: NO/NC. Интерфейс связи: IO-Link, IO-Link V1.1, COM3 (230.4 kbit/s).
Семейство: T-Easic FTS. При подборе сверяйте артикул 1091146 и полное обозначение FTS-I060F14A.
Примечания к параметрам (EN)
1. 1) All connections are reverse polarity and overload protected. Q1 and Q2 are short-circuit protected. Use an energy-limited circuit for the voltage supply as per UL61010-1 3. Outp. 2) Per output.
2. 1) Place probe tip in the center of the pipe to ensure the highest measurement accuracy. 2) The measuring range limit value depends on the medium used. 3) At medium temperatures above 100 °C, the distance between the bottom of the housing and the top of the process connection adapter must be at least 25 mm. If a SICK process connection adapter is used, the 60 mm probe cannot be used at process temperatures above 100 °C because the distances cannot be maintained. 4) According to the Pressure Equipment Directive 2014/68 / EU: Good engineering practice, according to Article 13 for media of media group 2 (other substances).
3. 1) According to the UL approval: degree of contamination 3 (UL61010-1: 2012-05); air humidity: 80% at temperatures up to 31 °C; installation altitude: max. 3,000 m above sea level.
4. 1) Only with M12 male connector attached / not UL-tested.
5. 1) Under reference conditions with water, diameter of inner pipe 25 mm, vertical installation in pipe, probe tip in tube center, fully-filled pipe without air bubbles, speed from 10 cm/s to 100 cm/s, inlet zone > 30 cm, outlet zone > 30 cm, 26 °C ± 1 °C, 2 bar ± 1 bar. 2) Filter off. 3) Under reference conditions with water, pipe diameter 25 mm, vertical installation in pipe, tip in pipe center, fully-filled pipe without air bubbles, speed = 100 cm/s, inlet zone > 30 cm, outlet zone < 30 cm, 26 °C ± 1 °C, 2 bar ± 1 bar.
Технические характеристики
- Модель
- FTS-I060F14A
- Напряжение питания
- 9 V DC ... 30 V DC 1) (прим. 1)
- Коммутационный выход
- 2xPNP
- Выходной сигнал
- 2 push-pull digital outputs (Q2 configurable for IO-Link; Q2 configurable as pulse output / digital input) for flow and temperature
- Функция выхода
- NO/NC
- Интерфейс связи
- IO-Link, IO-Link V1.1, COM3 (230.4 kbit/s)
- Подключение
- M12 round connector x 1, 4-pin
- Присоединение к процессу
- Without process connection (adapter needed for installation)
- Разрешение
- 0.01 m/s Speed; 0.1 L/min volume; 0.1% relative (via IO-Link)
- Температура процесса
- –40 °C ... +150 °C 3) (прим. 2)
- Температура окружающей среды при работе
- –40 °C ... +70 °C 1) (прим. 3)
- Степень защиты
- IP67 1) (прим. 4)
- Время отклика
- < 2.5 s 2) (прим. 5)
- Давление макс. (Бар)
- 100
- Диаметр зонда (мм)
- 8
- Диапазон измерения (см/с)
- 3-150
- Измерение температуры
- да
- Измеряемая среда
- Water and oil-based liquids
- Класс защиты
- III
- Масса
- 74 g
- Материал корпуса
- VISTAL® (PA66+PA6I GF50) (прим. 4)
- Наличие дисплея
- да
- Резьба разъема
- M12
- Серия
- T-Easic FTS
- Температура эксплуатации (°C)
- -40…+150
- Тип датчика потока
- Калориметрический (в корпусе с зондом)
- Единица продажи
- шт
- Артикул производителя
- 1091146
Не нашли точную модель?
На отдельной странице можно распознать маркировку по фото или загрузить BOM из Excel, Word и CSV.
